Product ID:D-DELTAMAX, TAPE WOUND & BOBBIN CORES (SUPD
MSDS Date:01/05/1987
FSC:9650
NIIN:00N030404
MSDS Number: BNMWT

ARNOLD ENGINEERING CO

300 WEST STREET
MARENGO, IL 60152
US

Emergency Phone: 815-568-2303

Info Phone: 815-568-2303

Preparer: K.L. LATIMER

Cage: 95566

ARNOLD ENGINEERING CO DIV OF SPS TECHNOLOGIES

G MARENGO, IL 60152 US

Telephone: 815-568-2000

Cage: 95566

NICKEL (SARA III)

CAS: 7440-02-0

RTECS: QR5950000

Fraction By Weight: 48%

OSHA PEL 1 MG/M3

ACGIH TLV: 1 MG/M3

IRON

CAS: 7439-89-6

RTECS: NO4565500

Fraction By Weight: BALANCE

OSHA PEL 1 MG/M3 (FE)

ACGIH TLV: 1 MG/M3 (FE)

LD50 LC50 Mixture:NONE SPECIFIED BY MANUFACTURER.
Routes of Entry: Inhalation:YES Skin:NO Ingestion:YES
Reports of Carcinogenicity:NTP:YES IARC:YES OSHA:NO
Health Hazards Acute and Chronic:PRIMARY ROUTE OF ENTRY:INHALATION OF
GENERATED AIRBORNE DUSTS OR FUMES. ANY LONG TERM EXPOSURE TO DUSTS
EXCEEDING RECOMMENDED TLV LEVELS MAY RESULT IN IRRITATION TO UPPER
RESPIRATORY TRACT. DUSTS IN E YES MAY CAUSE IRRITATION. PROLONGED
SKIN CONTACT WITH NICKEL MAY CAUSE ALLERGIC REACTION IN SENSITIVE
(EFTS OF OVEREXP)
Explanation of Carcinogenicity:NICKEL:ANTICIPATED TO BE A CARCINOGEN
(NTP) , GROUP 2B (IARC)
Effects of Overexposure:HLTH HAZ:INDIVIDUALS. AVOID INGESTION OF DUSTS
BY NOT EATING, DRINKING OR SMOKING IN AREA WHERE DUSTS OR FUMES ARE
GENERATED.
Medical Cond Aggravated by Exposure:NONE SPECIFIED BY MANUFACTURER.

First Aid:EYES:FLUSH WITH WATER FOR AT LEAST 15 MINUTES.
INGEST:IMMEDIATELY CALL MD . INHAL:REMOVE TO FRESH AIR. SUPPORT
BREATHING (GIVE O2/ARTIFICIAL RESPIRATION) . SKIN:FLUSH WITH
COPIOUS AMOUNTS OF WATER .

Flash Point:NON-COMBUSTIBLE
Extinguishing Media:MEDIA SUITABLE FOR SURROUNDING FIRE .
Fire Fighting Procedures:USE NIOSH/MSHA APPROVED SCBA AND FULL
PROTECTIVE EQUIPMENT .
Unusual Fire/Explosion Hazard:FINE METAL POWDERS MAY CAUSE EXPLOSIVE
HAZARD.

Spill Release Procedures:DUST MAY BE SWEPT WET OR VACUUMED TO KEEP
AIRBORNE DUST CONCENTRATIONS TO A MINIMUM.
Neutralizing Agent:NONE SPECIFIED BY MANUFACTURER.

Handling and Storage Precautions:USE GOOD MANUFACTURING PRACTICES AND
GOOD HOUSEKEEPING PRACTICES THAT WILL KEEP GENERATED DUSTS TO A
MINIMUM.
Other Precautions:GRINDING OR MACHINING OPERATIONS SHOULD BE PERFORMED
USING COOLANTS TO REDUCE DUSTS.

Respiratory Protection:IF AIRBORNE CONCENTRATIONS EXCEED THOSE
SPECIFIED, NIOSH/MSHA APPROVED RESPIRATOR SHOULD BE USED.
Ventilation:ADEQ LOC EXHAUST VENT SHOULD BE USED WHEN DRY GRINDING/
MACHINING ALLOYS TO KEEP EXPOSURE LEVELS BELOW RECCOMMENDED TLV.
Protective Gloves:PROTECTIVE GLOVES.
Eye Protection:CHEMICAL WORKERS GOGGLES .
Other Protective Equipment:NONE SPECIFIED BY MANUFACTURER.
Work Hygienic Practices:USE GOOD PERSONAL HYGIENE PRACTICES. GOOD
HOUSEKEEPING PRACTICES TO KEEP GENERATED DUST TO A MINIMUM.
Supplemental Safety and Health
MFR'S TRADE NAME/PART NO:USING NICKEL-IRON ALLOY.

HCC:N1
Spec Gravity:8.25
Solubility in Water:NOT SOLUBLE
Appearance and Odor:SILVER-GREY WITH NO ODOR.

Stability Indicator/Materials to Avoid:YES
POWDERS/DUSTS FROM PRODUCT ARE INCOMPATABLE W/STRONG OXIDIZING AGENTS
SUCH AS NITRIC ACID.
Stability Condition to Avoid:GENERATION OF AIRBORNE DUSTS.
Hazardous Decomposition Products:NONE SPECIFIED BY MANUFACTURER.

Waste Disposal Methods:DISPOSE IN ACCORDANCE WITH LOCAL, STATE AND
FEDERAL REGULATIONS.

Disclaimer (provided with this information by the compiling agencies):
This information is formulated for use by elements of the Department
of Defense. The United States of America in no manner whatsoever,
expressly or implied, warrants this information to be accurate and
disclaims all liability for its use. Any person utilizing this
document should seek competent professional advice to verify and
assume responsibility for the suitability of this information to their
particular situation.